It depends on how much hot water your household uses in its busiest hour, not on square footage. Size a tank by its first hour rating, matched to your peak hour demand. Size a tankless unit by flow rate and temperature rise. Both methods come from the U.S. Department of Energy.
I’m Kevin, owner of My Guy Plumbing. “What size do I need?” comes up on just about every water heater job. Too small and somebody gets a cold shower. Too big and you pay to keep water hot that nobody uses. Here’s how to work it out, using the method the U.S. Department of Energy (DOE) lays out.
Tank Water Heaters: Use the First Hour Rating
Don’t size a tank by its gallons alone. DOE says to size a storage water heater, including a heat pump water heater with a tank, by its first hour rating: how many gallons of hot water it can deliver in an hour, starting with a full tank. That number depends on the tank size and on how big the burner or element is.
Where to find it. On the yellow EnergyGuide label, top left, listed as “Capacity (first hour rating).” DOE notes the Federal Trade Commission requires that label on new conventional storage water heaters but not on heat pump water heaters, so for those, check the manufacturer’s literature.
What to look for. A first hour rating that at least matches your household’s peak hour demand.
Figure Your Peak Hour Demand
Pick the busiest hour of the day in your house. For most families that’s the morning rush or right after dinner. Then add up the hot water used in that hour with DOE’s averages:
| Use | Average gallons of hot water each time |
|---|---|
| Shower | 20 |
| Shaving | 2 |
| Hand dishwashing or food prep | 3 |
| Automatic dishwasher | 7 |
| Clothes washer, top-loader | 25 |
| Clothes washer, front-loader (H-axis) | 15 |
Example: three showers (3 × 20 = 60), one shave (2), and some hand dishwashing (3) in the same hour adds up to 65 gallons. That house needs a water heater with a first hour rating of at least 65 gallons. If the dishwasher or a load of laundry runs in that same hour, add it in.
DOE says these are estimates based on averages, and the worksheet estimates your busiest hour, not your total daily use.
Tankless Water Heaters: Flow Rate and Temperature Rise
A tankless unit doesn’t store water, so it’s sized by how many gallons a minute it has to heat, and by how much.
- Add up the flow rate. List everything that could run at once and add the gallons per minute (gpm). DOE’s example: a 0.75 gpm faucet plus a 2.5 gpm shower is 3.25 gpm.
- Figure the temperature rise. That’s the temperature you want out minus the temperature coming in. DOE says most uses need 120°F, and to assume 50°F incoming water unless you know otherwise. That’s a 70°F rise.
- Match the unit. DOE says a 70°F rise is typically possible at about 5 gpm through gas-fired tankless units and 2 gpm through electric ones. Check the manufacturer’s chart at your temperature rise.
DOE also says most tankless units put out 2 to 5 gallons a minute, and that running a shower and the dishwasher at the same time can stretch one unit. Some homes install two.
Measure Your Own Incoming Water
DOE’s 50°F is a stand-in. You can do better: hold a thermometer under a cold-water faucet, as DOE suggests, and let it run for a minute first. Check it more than once a year. If the reading changes with the seasons, size a tankless unit for the coldest one, because the colder the water coming in, the fewer gallons a minute the unit can heat.
A Few More Things That Matter in Bozeman
- Hard water. Bozeman’s water is moderately hard, and mineral scale builds up in any water heater. See our Bozeman water quality guide and water softening.
- Don’t crank it to 140°F to make a small tank go further. DOE warns that 140°F raises the risk of scalding.
- Heat pump water heaters are sized like tanks, by first hour rating. For incentives and the tank vs. tankless vs. heat pump question, see our water heater installation in Bozeman page.
- Permits. Replacing a water heater usually involves a permit in Montana.
Your Sizing Checklist
- Pick your household’s busiest hour for hot water
- Add up the showers, dishes, and laundry in that hour (DOE averages above)
- Tank or heat pump: find the first hour rating on the EnergyGuide label or spec sheet, and make sure it at least matches
- Tankless: add up the gpm of fixtures that run at once
- Measure your incoming water temperature at a cold tap, more than once a year
- Tankless: check the unit’s flow at your temperature rise
Questions We Hear
How do I find a water heater’s first hour rating?
Look at the yellow EnergyGuide label. The U.S. Department of Energy says the first hour rating is listed in the top left corner as “Capacity (first hour rating).” Heat pump water heaters don’t have to carry that label, so check the manufacturer’s spec sheet.
Is a 50-gallon water heater big enough for a family of four?
Gallons alone won’t tell you. Size by first hour rating, not tank size. Add up the hot water your family uses in its busiest hour, using about 20 gallons per shower, and pick a heater whose first hour rating at least matches. Two 50-gallon tanks can have different first hour ratings.
What incoming water temperature should I use to size a tankless water heater?
Measure it. Hold a thermometer under a cold-water faucet. If you can’t, the U.S. Department of Energy says to assume 50°F unless you know otherwise. If your reading changes with the seasons, size for the coldest one, since colder water lowers how many gallons a minute a unit can heat.
Need a New Water Heater?
My Guy Plumbing repairs and replaces tank, tankless, and heat pump water heaters in Bozeman and the Gallatin Valley. We’re locally owned, licensed, bonded and insured (Montana plumbing license #15401), with free estimates and 24/7 emergency service. Text a photo of your current water heater’s label and we can talk sizing. Call or text (406) 600-2177, or contact us online.
If we’ve helped you out, I’d appreciate a Google review. It helps other folks in Bozeman find a local plumber.
Notes and Sources
Sources checked October 28, 2026. DOE’s Energy Saver pages were taken down from energy.gov in 2026 (both URLs now return 404), so the archived copies are cited with the original addresses.
- U.S. Department of Energy, Energy Saver, Sizing a New Water Heater. Size storage and heat pump (with tank) units by first hour rating, gallons per hour starting with a full tank; listed on the EnergyGuide label as “Capacity (first hour rating)”; FTC requires the label on conventional storage units but not heat pump units; look for a first hour rating that at least matches peak hour demand; worksheet averages (shower 20, shaving 2, hand dishwashing or food prep 3, automatic dishwasher 7, top-loader 25, H-axis washer 15); estimates are based on averages; worksheet doesn’t estimate daily use; tankless sizing by flow rate and temperature rise; 0.75 + 2.5 = 3.25 gpm example; 120°F for most uses; assume 50°F incoming unless you know otherwise; a thermometer under a cold-water faucet; 70°F rise at about 5 gpm (gas) and 2 gpm (electric); 140°F increases scalding risk. Original URL https://www.energy.gov/energysaver/sizing-new-water-heater, archived copy: https://web.archive.org/web/20250601030316/https://www.energy.gov/energysaver/sizing-new-water-heater. Also listed in PNNL’s Building America Solution Center (DOE, Nov. 2024): https://basc.pnnl.gov/library/sizing-new-water-heater-0
- DOE’s worksheet example lists 3 showers, 1 shave, and 1 hand dishwashing as “66” gallons, but those numbers add to 65. The post uses 65.
- U.S. Department of Energy, Energy Saver, Tankless or Demand-Type Water Heaters. Most units deliver 2 to 5 gallons per minute; gas units have higher flow rates than electric; simultaneous uses can stretch a unit; two or more units are an option. Original URL https://www.energy.gov/energysaver/tankless-or-demand-type-water-heaters, archived copy: https://web.archive.org/web/20250601032848/https://www.energy.gov/energysaver/tankless-or-demand-type-water-heaters
- ENERGY STAR, Residential Water Heaters Key Product Criteria. Background on how first hour rating is tested and used for qualification: https://www.energystar.gov/products/water_heaters/residential_water_heaters_key_product_criteria
- PNNL Building America Solution Center, DHW First Hour Rating tool (AHRI-based), for readers who want to look up a model’s rating: https://basc.pnnl.gov/redcalc/tool/dhw-first-hour-rating
- Bozeman incoming water temperature: no public source found for a Bozeman-specific figure, so the post gives none. It uses DOE’s 50°F default and DOE’s advice to measure at a cold tap.
- Hard water: the site’s own /bozeman-water-quality/ page.
